The new X6 with an identical frontal area to the coaxial V6 however, that’s where any similarities end.
X6 technology sees the use of a powerful neodymium magnet structure housing two independent voice coils. Both sections within the X6 driver handle their own dedicated frequency bands with the upper mid and HF sections exiting through a common, centrally mounted horn assembly.
Compact, lightweight and versatile are the requirements fulfilled by this superb Shermann cabinet. For use as foldback or fills in theatre touring systems, as FOH or fills in AV and product launch environments, installed as fills in theatres and churches, flown discretely at fashion shows or just used as a small vocal PA the X6 offers the owner or hirer a wide world of high quality sonic opportunities.
Return to the simple ways of successfully using a X6 with the amazing Shermann XB12 bass system per side – a simple four cabinet rig offering substantial performance successfully operated by lower power amplification.
The 6· ” LF section.
The X6 is equipped with a 37mm voice coil within a Ferrie magnet structure housed in a cast aluminium chassis . Four M5 mounting bolts secure the drive unit to the baffle board
The upper Mid/HF section.
A 25mm voice coil drives a composite diaphragm for frequencies between 2.3KHz and 20KHz. These frequencies exit the driver from a dedicated horn assembly located above the bass/mid driver.
The V6 cabinet.
Built from Eastern European birch plywood the V6 is capable of being used as a wedge monitor at two distinct angles. A steep 50° angle allows close to mic’ stand operation whilst a shallower 20° angle allows the X6 to be placed on the Shermann sub for use as a keyboard monitor. For flying purposes the 6 is equipped with 8mm flying points to accept our multi-purpose flying/stand mount bracket. For speed of rigging a K&M 35mm stand mount allows the 6 to be placed on a stand or pole in seconds. An insert handle is fitted at the rear of the cabinet allowing quick and simple handling of this lightweight cabinet. Finally, the gigging version of the 6 is coated with a dense, heavy duty textured material we’ve named S-Coat. The coating is extremely durable and it’s been proved that S-Coat retains its ability to protect the cabinet far longer than conventional paint finishes.
The 6 is a high technology loudspeaker that’s a pleasure to use and a greater pleasure to perform with. It’s super compact, durable and lightweight. With or without subs the 6 allows the engineer great freedom of set-up whilst it’s clear response in wedge mode allows artists to hear their performances precisely and accurately.
Warning. It should be remembered that the 6 is capable of moderately high pressure levels therefore care should be taken in their positioning with regard to your audience or artists.
No responsibility will be accepted by the manufacturers, distributors or sellers for the incorrect or foolish use of loudspeaker systems.
Format 2 Way Passive
Passive Networks PSN3
Nominal Impedance 8 ohms
HI-Pass Filter (-3dB) 70Hz / 4th / 8th Order
Hi-pass with Sub 120HZ / 4th Order LR
Power @ 8 ohm 150w AES
Sensitivity @ 1w/1m 92dB
O/P level at Rated Power 115dB @ 1m
Frequency Range 80Hz – 19.5kHZ (+-3dB)
Dispersion above 1500Hz 60 x 50
Drive unit – LF section
Drive unit size 165mm / 6.5″
Voice Coil diameter 37mm / 1.5″
Chassis pressed steel
Mounting 5mm caphead bolts x 4
Drive unit – Mis/HF Section
HF section exit 25mm / 1″
Voice coil 25mm / 1″
Horn Mounting part of LF structure
Height 344mm – 13.5″
Depth 210mm – 8.25″
Width 210mm – 8.25″
External Volume 15 lts – 0.53ft
Weight 7kgs – 15.4lbs
Panels 12mm birch ply
Baffle 18mm birch ply
Cabinet external SW-Coat (S-Cost option)
Handles Top Flip
Grille Coated Steel Mesh
Iputs NL4 x 3
Connection Pins 1+ 1-
Flying and Stand Mount Hardware
Stand mount – fitted 35mm
Flying Points – option 8mm inserts